Our Rust Remover has many uses...
Automotive
As we all know... Cars eventually rust and it is very expensive to replace many of the parts. Car parts that typically rust are brake calipers, trailer hitches, chains, manifolds, exhaust components and many more. Everyone needs to remove rust from cars. We have the safest rust remover, by far.
These parts can be easily "rejuvenated" and completely rust free by using our rust remover. Turn your rusty car into something you can show. This is the best rust dissolver for your rusty car.
Industrial
Industry can not tolerate rusty parts in their assembly lines. Our rust remover can easily be retrofitted into an cleaning line, or use it as a stand alone dip tank. Simply immerse your parts in a dip tank and remove when parts are free of rust. Our product is free rinsing, making it easy to prep prior to a paint line or operation.
Tanks can be cleaned, inside and out, using our Un-Rust-It. No need to sand blast or grind away the rust. Applications can include continuously spray or fill the tank up with rust remover. The Un-Rust-It can be reused over and over until the solution becomes black and the rust removing stops. Don't be fooled by evapo ration rust removers.
Military
There are many military applications. Tank tracks, engines, exhausts, are just a few. You can even use this in the field. Just spray it on until the rust dissolver removes the rust for you. Catch the spray on a tarp or plastic sheet and recirculate it back onto the vehicle or part. Super easy to use. Since its non-hazardous, its safe to use and spillage is typically not a big issue.
Immersion tanks will accommodate large parts, simply lower the engine block into the solution and remove when rust is dissolved. Our concentrate makes it incredibly easy to make a batch of the powerful rust removing fluid. Just add concentrate and then add 9 or 4 equal parts of water to make 10% or 20% solution, respectively.
Tractors and Farm Implements
Farms have many applications for the Un-Rust-It Industrial Concentrate. You can remove the rust from even the most severe applications. Just find an old water tub, pour our concentrate into the tank and add water according to your mix ratios.
Find your rustiest wrenches, plows, nuts and bolts, or whatever and immerse it into the tank until the rust is gone. When you are done, reuse the solution by pouring it into an old drum and cover it. When more rusty objects are available, just uncork the drum and reuse the solution.
Home
Residential uses are abundant.. If you have kids, how many times have you found your tools laying in the yard and covered in rust. Why pay to purchase new ones or waste your time with the WD-40?
Simply cut the top out of an old mike jug and use it for a container. Fill it with a quart of concentrate and top off with water. Immerse your tools into the solution and wait till the rust has been removed. Old crescent type wrenches work like new.
Antique Restoration
There are plenty of applications for antiques. We have museums purchasing our products to remove rust from valuable artifacts. Immerse your antiques whole, our fluid will not harm paints, rubbers, and plastics. In fact, you can save the antiques by not having to pry or other wise damage the antique while trying to dismantle the object.
Our rust remover also works on coppers and copper based alloys such as brass and bronze.. Our fluid does a great job on brightening these metals by removing the copper oxides off the surface.
Un-Rust-It will remove rust from fragile sheet metal parts and other steels to remove the oxides, leaving the steel behind. You couldn't do this with a sand blasting or sanding operation!
Construction
How many tools and construction equipment is left in the back of a pickup to rust? Contractors are constantly leaving their tools outside, and they end up rusting. When they need the tools, the rust prevents them for working.
Just find an old 5-gallon pail, and make up a solution. Place your tools into the fluid and check them the next morning. The rust will be removed and we also provide a indoor rust inhibitor to reduce the amount of rusting. Just spray or metal Shield 1999 onto the tools and let dry. The fluid dries to touch and is great for indoor use.
Tools
Expensive rusty tools are the perfect application for our rust removers. It does not harm the chrome plating and removes rust from the hard to get at areas.
The rust will be removed from anything the fluid can "see" or get to. Un-Rust-It Industrial Concentrate can remove the rust from even the most severe applications.
Find your rustiest wrenches, screwdrivers, squares, vise grips, sockets, and other tools and immerse it into the tank until the rust is gone. When you are done, reuse the solution by pouring it into an old 5-gallon pail or milk jug and cover it. When more rusty objects are available, just uncork the container and reuse the solution.
Gas Tank Restoration
Rust accumulates insides of gas tanks, especially older ones. Now it is easy to remove this rust without using dangerous acids or sand blasting.
Remove old gas and pour about 1-2 ounces of Metal Kleener 0001 or similar detergent (non-caustic type), fill half way with hot water and shake to remove all the varnish and dirt that may be in the tank. Then simply pour our Rust Remover solution into the tank, add the appropriate amount of water (hot if available) and let set overnight.
Un-Rust-It will all the remove rust from the insides of the tank. If you fill the tank up a little more than half way, then you can remove the rust from one side and flip the tank over to remove the rust from the other side.
Compressor Tanks
Compressor tanks hold water that condenses during the compression of the air. Typical compressor tanks are steel and are subject to rusting. This is why water comes out of the little valve on the bottom of the tank when you open it.
This same valve is notorious for clogging after you blow it out once. The rust gets stuck on the valve and causes it to seat incorrectly. As simple solution to fix this problem is to add about 1/5th the capacity of the tank with Un-Rust-It solution and let stand overnight. Then simple blow out the valve the next morning. No need to rinse tank, the remaining rust remover will act as an rust inhibitor.
Our fluid will not hurt the valves and seals. Its a perfect solution to a problem like this. Save the fluid and you can reuse it later. Just keep it covered to minimize further contamination and evaporation of the product.
Brake Calipers
Brake calipers are easy to clean up and paint using our Un-Rust-It Industrial rust remover. Our solution will not hurt rubber, plastics and existing paint.
All you have to do is remove the caliper from the wheel assembly and remove any loose rust. No need to remove the brake hose or rubber boots. Find a bowl or other container that the caliper can fit into. You may have to prop it up on a concrete block or similar. Place the caliper into the container and fill with 20% Industrial Concentrate Rust Remover until the caliper is submersed and let it set overnight or until the rust is removed.
After you remove the caliper from the solution, wash off the caliper with diluted Metal Kleener 0001, rinse and let dry. You can paint it with high temp paint when dry.
Removing the rust from the calipers will make it operate smoothly and keep it from binding.
The rotors can be done in the same manner except remove them from hub and place into a plastic container with enough Industrial rust remover and water to cover it.
Gun Bluing Remover
Gun bluing is easily removed using our 10% solution of Industrial Concentrate. Just takes minutes to remove the bluing.
Removes the bluing off from all your gun restoration projects. Also, removes the rust without destroying the metal on the barrels.
What Makes Un-Rust-It the best in Rust Removal
- Concentrate Savings: Our competitors rust removers are pre-diluted and ready to use (RTU). Our Rust Remover is CONCENTRATED to save you money, consequently, we can offer you the lowest price. Why Pay for more shipping charges and pre-diluted products?
- 2x better: Our 10% solution of industrial concentrate mixed with your regular tap water is 2x better than other rust removers on the market today. Our rust remover dissolves and removes 2x as much iron oxide (rust) in less time. Check out our Example Pictures...
- Concentrate SHOOTER: Makes 1-gallon of rust remover that is 4x stronger than our competitors, just add your water. Costs less to ship... We pre-mix the shooter to make a 20% solution for your tough rust removal jobs.
- Less Expensive: Our concentrate SHOOTER is less expensive. Add water to make one-gallon for about $17.50/gallon as compared to $20/gallon or more for the others!
- Reduced Shipping Costs: We offer a concentrate to reduce shipping costs and storage issues. Why buy 10 gallons of the competitors product when you can do the same with 1-gallon of Un-Rust-It Industrial Concentrate?
- $5.95/gallon: Our Industrial Concentrate is $59.50 per concentrated gallon and makes up to 10 gallons. That is $5.95/gallon- lets see our competitors beat that.
- Save on Shipping: 1-gallon verses 10-gallons of their equivalent. That equals a huge savings on shipping.
- Also acts like an Rust Inhibitor: A clean solution of our 10% concentrate also acts like a short term rust inhibitor when parts are re-immersed into the fluid and let dry. Or just use our Metal Shield 1999 for long term rust preventative, up to 12 months indoors.
- Use our Metal kleener 0001: Metal Kleener 0001 is designed specifically to remove oils, greases and dirt prior to rust removal and also to remove the black smut that may be left on some parts after rust removal.
- BONUS: Removes Gun Bluing, oxides on copper/brass, and some black oxides.
- We're not out to take advantage of you! Many of the competitors water down their products and increase their pricing to you, we give you options and substantially lower prices.
- Rust Information: We have a good primer on RUST. What is RUST? and much more..
- Money Back Guarantee: We want you to be happy with our products and have a money back guarantee . We offer engineering support and have chemical engineers to guide you in the right direction...
- Great Products, Great Prices and Knowledgeable too!!!!!
- Don't forget our Chemical Engineering Services, just call...
